Does anyone happen to know how the Neko Project II emulator works? I can't figure it out for the life of me. If I want to play, say, Farland Story, how would I go about doing so?
Printable View
Does anyone happen to know how the Neko Project II emulator works? I can't figure it out for the life of me. If I want to play, say, Farland Story, how would I go about doing so?
And thats the easy one to use :P
okies first you not only need the emulator but you also need the font file, you can put the font file in a seperate folder let call it font LOL
Just get the font from Zophars domain, the one listed as Japanese Font for the anex86 will do just fine.
Once you have the font file run NP2 and click on emulate then Font... and select the font file you just downloaded and put in the font folder
Next click screen then Screen option... and click the Chip tab and make sure it's set to uPD7220 - GRCG+ and Enable 16color
Now all that is set click on HardDisk then SASI-1 and Open and select the extracted hdi file
Now Click
Emulate then Reset
**For Farland Story 1 only
To view the intro, aswell as having set SASI-1 you need to set the fdi to FDD-1
Also for the main game after it has loaded it also needs that fdi aswell
P.S. the games are mouse games so once it start click on your middle mouse button for it to be used by the emu, the same middle click is used to release the mouse from the emu aswell
So.. unbeleivably..complicated @.@; I'll give it a shot, though. Thank you
EDIT: I can't find that font thing. I'm currently searching around Zophar's Domain, but I don't see it anywhere. I don't even have a clue where to start looking. I don't see anything about anex68 or neko project II at all
Not particually I just went into a bit of detail thats all, anyway let me know if you get it working or not :)
Your blind :P find it at http://www.zophar.net/pc98.html look for Japanese Font it's like the 2nd file there
I found it right before you posted that. *sweatdrops* I'm sorry about that. Anyhoo, I've got it working now. Thank you so much. To play the other games, will I have to do that complicated setup thing again? If so, I'll just copy your instructions and paste them into wordpad so I won't lose them. Now I just have to get all the other Farland games.. I only have Farland Story 5 so far ^.^;;
Once NP2 is set up it's set up all you do is set SASI-1 to the hdi you want to play and click emulate then reset, it's only FS1 that theres a fdi used aswell
I managed to load Farland 1 , using the instructions here, however I can't get the game to respond to any commands, just keeps replaying the intro.
Nothing works,the mouse (yes I did also middle click) I can see the cursor but nada, keyboard option doesn't work, joystick, nada =(.
any help plz?
Thanks!
Alusnova
don't start the emu up with the floppy inserted ;)
Quote:
don't start the emu up with the floppy inserted
Floppy?
All I did was follow instructions as you said here, also tried the Anexwhatever emulator, same idea, no response from any kind of controls. =(
Alus
fdi = floppy disk imageQuote:
Originally Posted by Zorlon
so when you want to play the main game start without the fdi and when you are propted then use the fdi
got it working now?
I think that "anex86" is a lot easier to use and configure
maybe you should try this emu instead :)
(oh yes floppy is the .fdi file and hard disk is the .hdi file if I remember correctly)
Edit: You were faster Zorlon :D
Neh it's much harder to use :P plus it uses more resorces
Edit
I have done guides for anex86 aswell for the same games aswell lol, the first time I mentioned them here a few years back
I sorta understand what you guys are saying , still no luck, here is what I did:
Try #1: Ran Neko II --> FDD1 -->Open-->Farland Intro Boot Disk .fdi
Also nothing under HardDisk .
Message I got was " Disk A Needed , left click when ready"
TRY #2: I tried loading HDI file without the FDI one and nothing happens.
When I load both files , plays the intro, no response whatsoever.
Also tried loading just the HDI file with Anex and took me to an A:\ command promt.
sigh......
TRY #2: I tried loading HDI file without the FDI one and nothing happens.
after you do that goto emulate then reset
you will then get the message Disk A Needed
why you done Try #1 I don't know at all, and how you got the message that you got is impossible if you done what you said you done :/